INCLUDES: DS1A - 1 1/2" Hollow Octagon DS1B - 2" Hollow Octagon DS1C - 2 1/2" Hollow Octagon DS1D - 1 1/2" Hollow Star DS1E - 2" Hollow Star DS1F - 2 1/2" Hollow Star The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS1A - 1 1/2" Hollow Oval DS1B - 2" Hollow Oval DS1C - 2 1/2" Hollow Oval DS1D - 1 1/2" Hollow Triangle DS1E - 2" Hollow Triangle DS1F - 2 1/2" Hollow Triangle The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS3A - 1 3/4"x11/16" Fancy Flat Top Bar DS3B - 1"x7/8" Round Top Trim DS3C - 7/8"x1/2" Concave Top Trim DS3D - 3/4"x5/8" Concave Top Trim DS3E - 1 3/4"x3/4" Scalloped Top Bar DS3F - 2 1/2"x1" Fancy Convex Bar DS3G - 2 7/8"x1 1/2" Fancy Hollow Dome The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS4A - 1 1/2" Hollow Heart DS4B - 2" Hollow Heart DS4C - 2 1/2" Hollow Heart DS4D - 1 1/4" Hollow Diamond DS4E - 2" Hollow Diamond DS4F - 2 1/2" Hollow Diamond The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS5A - 1 1/2" 5 Point Scallop DS5B - 2" 5 Point Scallop DS5C - 2 1/2" 5 Point Scallop DS5D - 1 1/2" 4 Point Scallop DS5E - 2" 4 Point Scallop DS5F - 2 1/2" 4 Point Scallop The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS9A - 1" Handle DS9B -1 1/2" Handle DS9C - 2" Handle The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS11A - 2"x2" Tray DS11B -2 1/2"x2 1/2" Tray DS11C - 3"x3" Tray The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS12A - 2"x1 1/4" Tray DS12B -2 1/2"x1 1/2" Tray DS12C - 3"x2" Tray The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS13A - 3"x1 5/8" Flared Tray DS13B -3 1/4"x1 7/8" Flared Tray DS13C - 3 1/2"x2 1/8" Flared Tray The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
Extrudes 1” solid octagon, 1” star, 1” triangle and 1 1/4” oval, all solid. Requires Die Mask 925DM, which is included with die. The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive. 925A - Large Coils 3/4", 7/8", 1", 1 1/4" 925B - 2" Solid Ribbon 925C - 3" Solid Ribbon 925D - 1 1/2" Hollow Round 925E - 2 1/2" Hollow Round 925F - 1 1/2" Hollow Square 925G - 2 1/2" Hollow Square 925H - 1 1/2" Hollow Hexagon 925J - 2 1/2" Hollow Hexagon 925DM - Die Mask (Neoprene) 957 - Stainless Steel Brace *This Set #925 and Set #915 are included in every Stainless Steel Extruder Pkg.
4" Expansion Box Wooden Dit Kit for 4" Extruders. Marine grade plywood inner and outer dies to make circle, square, and hexagonal shapes. Extrusion wall thickness 1/2". The Wooden Dies will produce 6" diameter extrusions. Use of this Die Kit requires the 4" Aluminum Expansion Box. Made in the U.S.A.
GR Pottery Forms are wood drape molds ideal for making dinnerware and serving platters. They are cut and beveled fiberboard which make them durable and economical. Easy to use over and over again giving you a tool to create your personalized shallow objects. Jeff has used them for 10 years to create his production line and now is offering them to you. But remember they are wood. They will not last as long if they are left in a wet condition for over a 24 hour period. The timing of making them and removing the pieces from the slab is very similar to plaster. Ship really well and can be easily stored in a dry space. No release agent, cleaning or sealing necessary. Try the "Foot Maker" tool to smooth and shape slab feet or edges. 3" Square spacers are available separately and can be used to lift the molds off the surface of the table after draping the slab so modifications can be made to the edges. Take a look at the videos below (or check out all of the videos on the GR Pottery Form YouTube channel) to learn some tricks and tips on how to use the GR Pottery Form Molds.
INCLUDES: (1) WA (1) WA Board (1) Round 5" (1) Round 6.5" (1) Round 8" (1) Round 9.5" (1) Round 11 (4) WA Spacers (total) All forms measured in inches. Accessory to attach on the top of a potter's wheel to create (round) plates.
WA Spacers are an integral part of the GR Pottery Form's WA System which allows round forms to be mounted to a wheel head. For more details, watch our video below! *Each spacer comes with a pin.
Our OG Cutie Heart is a 4" Heart perfect for small trinket dishes, or pair with our larger OG Heart forms (available in 6", 8", and 10") to create a nesting set.
Each OG Form has a 45 degree angle edge, and 3/4" depth.
All Forms are measured in inches.
Use to assist with removing Wallies from the clay.
We recommend gluing in the pin to both the Wallie Form and the Spacer Pull with Elmer's or Wood Glue so that it is easier to remove the Form from the clay.
The WA2 is the master part of this System. It houses all the RD2 Forms with a 2-pin Key system.
Includes:
(1) WA2
(1) WA2 Key - Includes 2 Pins
(1) WA Board
Fits most U.S. standard wheel heads with 10" bat pins.
*** WA2 can also house the standard round Forms and Rim Templates by removing the outside pin.
Each Wallie Casserole Form has a 90 degree straight edge, and 2" depth.
When using the Wallie Forms, you should remove the clay after forming, and should not let the clay become dry on the Forms.
