Welcome to our new site. You are now welcome to shop and place your orders here. Use your email address to login. You will receive a confirmation code via email to checkout
This sieve is a stainless steel screen permanently fused in tough, flexible polyethylene. The diameter of the screen is 6" and sets perfectly into a 3½ or 5 gallon bucket. Potters typically use a 60 or 80 mesh sieve for most standard glazes. The higher the number the finer mesh screen.
Xiem's foam brush is made from the highest quality foam and is secured on a plastic handle for wax-resist application on pottery. It is also excellent for oxides, stains, inks, and glazes in hard to reach ares.
Small: .25" wide X4" long
Medium: .5" wide by .4.8" long
Large: .6" wide X 5" long
Available in 10 packs or 20 packs
These posts are safe to fire all the way up to cone 10. Square Kiln Post prices vary with height. If you have triangle posts, you can still use square posts in the same kiln load. It is more critical to make sure all of the posts under each shelf are the same height.
Pyrometric cones measure heat-work (the effect of time and temperature). They are slender pyramids made from about 100 carefully controlled compositions. Each cone number is unique in measuring temperature within a small temperature range (less than 30°C). Cones measure the amount of heat absorbed over time. As the cone nears its maturing range, it softens and the tip begins to bend, drawn down by the influence of gravity.Standard, or Large cones are used as witness cones to monitor the firing and verify temperature uniformity. A cone pack is necessary to support the cones during firing. If you have a kiln sitter on your kiln, you should use Junior cones.
Warning! Do not view cones above earthenware temperature with the naked eye as this may cause cataracts. View through welders goggles - sunglasses are not suitable as they filter out UV, but not the infra-red, which is the damaging wavelength in this case!
[click on the image thumbnails below to open/download the PDF for each]
Download SDS Sheet for Orton Cones
NOTE: The wax resist is colored with a pink or purple tint (that burns out completely), but the actual shade varies by batch. Recently we were sent a sample of the Mr. Mark’s Wax On. We enjoyed testing this wax resist and found it to be excellent for precision application on bisque fired ware. The light purple color, which completely burns out, makes it easy to see as you are applying it. The wax brushes on smoothly and dries quickly – about 5 minutes! The special hardening agent in this wax also ensures that any glaze that drips over onto the wax will wipe off easily with a wet sponge. Mr. Mark’s Wax On also works exceptionally well for the “Wax and Wipe” technique on leather-hard or bone dry clay. Apply the wax directly onto your un-bisque fired piece, (I tested it on both a fresh slab and on a bone dry piece), allow it to dry, then use a sponge to remove the clay from the bare places. The wax seals over the clay underneath it, leaving those areas raised. After bisque-firing, you’re left with a nice embossed (or debossed) texture. Mr. Marks’ Wax ON is a wax resist product that contains a special hardener that quickly sets the wax. It was created to eliminate problematic dripping and tacky surfaces when applying wax. Now you can decorate with wax during glazing without worrying about pesky smudges and sticky fingers. It is ideal for creating detailed, precise surface decoration on bisqueware and can be applied with either a brush or slip applicator. The pink/purple color allows you to easily visualize where wax is applied. However, the color burns out in the firing, just like regular wax. Wax ON should be stored at room temperature and mixed well before use. Brushes and tools used for application of Wax ON should be washed after use.
StudioPro SpaceSaver Bat System The SpaceSaver is a convenient system for making smaller pots and maximizing table space in your studio. The entire system is fully compatible with the now unavailable Wonderbat. It consists of a 14" adapter bat and 8- 6" insert bats. Both are made from a 1/2" exterior grade MDF which provides excellent bottom drying and rigidity. The adapter bat mounts on standard wheel-head pins with rubber "through hole" grommets making a true two-sided bat. Made from 1/2" exterior grade MDF "finger lifts" and rounded edges for easier removal, smoothness and longer wear Excellent bottom drying Rubber grommets spaced 10" on center for standard wheel pins Through-hole grommets make the SpaceSaver a true two sided bat
StudioPro Black Plastic Bats are a permanent solution to your bat needs. They’re easy to care for, extremely versatile, and a great choice for schools and art centers where pots are often left on bats for long periods of time. Our Plastic Bats are textured on both sides so clay adheres equally well on either surface: a true "two-sided" bat. They are cut from a high-quality marine grade High Density Polyethylene (HDPE), which is produced using a patented extrusion process. This ensures perfect flatness of every sheet and every bat! All bats are 1/4" thick EXCEPT for the 22" diameter bat which is 3/8" thick. The 8" and 10" bats work with the 12" bat adapter.
A 7" x 6¼" plaster sprig mold containing two sizes of turtles and frogs. To transfer the design to your clay slab, place slab on mold, and either use a heavy clay roller, or press firmly with your hands. Remove clay from mold and shape into any form you desire.
These are high quality, hand pressed, natural rubber texture mats. You will not be disappointed with the quality of these texture mats.
What really makes these texture mats stand out is that the mandala pattern itself is NOT recessed, or debossed, into the clay. The outline of the mandala is the part that is recessed/debossed. Hard to explain in words, super easy in pictures. See product photos to the left for details. It's a great effect that has been especially attention-grabbing for our early testers of these mandala texture mats.
An empty 2 ounce jar with lid. Perfect for storage of glazes, slips, and other liquids or materials. All-purpose straight-sided jars for storing and portioning glaze materials. Translucent for product visibility. Wide mouth for easy filling and pouring. Chemical and impact-resistant polypropylene. FDA compliant. Caps included.
An empty pint jar with lid. Perfect for storage of glazes, slips, and other liquids or materials. All-purpose straight-sided jars for storing and portioning glaze materials. Translucent for product visibility. Wide mouth for easy filling and pouring. Chemical and impact-resistant polypropylene. FDA compliant. Caps included.
4 ounce jar Repairs ~ Add-ons ~ Attaching flowers, ribbons, etc. ~ Repairs to broken pieces ~ Fixing hairline cracks ~ Attaching greenware to greenware ~ Attaching greenware to bisque ~ Attaching bisque to bisque ~ Removing hard spots ~ Acts like a wood putty for larger area fill-ins. Directions: Do not wet the piece(s). Stir well, apply with brush to both sides. Press pieces together and hold until they stick together, then re-fire.
2 ounce jar Repairs ~ Add-ons ~ Attaching flowrs, ribbons, etc. ~ Repairs to broken pieces ~ Fixing hairline cracks ~ Attaching greenware to greenware ~ Attaching greenware to bisque ~ Attaching bisque to bisque ~ Removing hard spots ~ Acts like a wood putty for larger area fill-ins. Directions: Fill to ridge above label with any high fire slip or clay and stir well. Do not wet the piece(s). Apply with brush to greenware or bisque. Let mender dry, clean, and then fire to normal slip/clay temperature.
CSI Turntables are made of two plastic laminate covered particle boards (plastic laminate design will vary from one to the other) with a stainless steel ball bearing, screwed into the inside surfaces of the boards. The 8" & 10" turntables have a 4" bearing capable of supporting at least 200# and the 12", 14" & 16" have a 6" bearing capable of supporting at least 300#. To clean, wipe with a damp sponge (do not submerge the turntable in water).
CSI Turntables are made of two plastic laminate covered particle boards (plastic laminate design will vary from one to the other) with a stainless steel ball bearing, screwed into the inside surfaces of the boards. The 8" & 10" turntables have a 4" bearing capable of supporting at least 200# and the 12", 14" & 16" have a 6" bearing capable of supporting at least 300#. To clean, wipe with a damp sponge (do not submerge the turntable in water).
CSI Turntables are made of two plastic laminate covered particle boards (plastic laminate design will vary from one to the other) with a stainless steel ball bearing, screwed into the inside surfaces of the boards. The 8" & 10" turntables have a 4" bearing capable of supporting at least 200# and the 12", 14" & 16" have a 6" bearing capable of supporting at least 300#. To clean, wipe with a damp sponge (do not submerge the turntable in water).
Mr. Mark's Removable Wax Off Resist is a wax we have created for potters and decorative artists. It is designed to be painted on like regular wax, but can easily be peeled away. The removal is simple and can be done in a short period of time. This allows for endless possibilities in design as well as layering. Our Wax Off! Resist drys in 5-10 minutes depending on how thick you put it on. It drys darker than it appears when wet (so you know when it's ready). It can even be applied to spots on your bisque ware that have already been dipped in glaze without lifting away the glaze. On top of all that it's affordable! You will never have to be afraid of dripping wax on your pots and being stuck with a waxing mistake again: now you can just peel it away! Helpful Hint: By resting your brush in soapy water while you are working with Wax Off, you will preserve the life of your brush. Clean your brushes with soap and water after use. Dish soap works great. There are no commercial preservatives in this product to prevent it from freezing. If your area of the world is freezing this product when exposed may harden. There are no refunds if this happens. Please be aware of your local weather.
Aftosa Wax Resist is used to resist glazes. It should be thinned with water to suit the potter's use. The wax is applied to the base and rims of the pieces before glazing. Allow the wax three to four hours to dry before glazing (some clean up with a sponge may be required) or before adding a second coat. Aftosa Wax Resist is also excellent for use in decorating pottery. Although Aftosa Wax Resist is tinted green so it is easy to see while you are working with it, the Wax Resist fires clear and the Black Wax Resist leaves a black line after being fired. The wax has a shelf life of 2-3 years. If used improperly, it can become contaminated. Always keep the lid tight on the original container. Pour a small amount in a separate container, use as desired, and dispose of the excess. Do NOT pour wax back into the original container. If the wax has a strong, sour odor, it has been contaminated. Clean up is easy with warm, soapy water. Please Note: The Wax will FREEZE in cold climates and will not resist effectively. If the wax has frozen, it will get lumpy and separate. Wax Resist will be sent to cold regions in the winter only at the customer's risk.
Aftosa Wax Resist is used to resist glazes. It should be thinned with water to suit the potter's use. The wax is applied to the base and rims of the pieces before glazing. Allow the wax three to four hours to dry before glazing (some clean up with a sponge may be required) or before adding a second coat. Aftosa Wax Resist is also excellent for use in decorating pottery.
Although Aftosa Wax Resist is tinted green so it is easy to see while you are working with it, the Wax Resist fires clear and the Black Wax Resist leaves a black line after being fired. The wax has a shelf life of 2-3 years. If used improperly, it can become contaminated. Always keep the lid tight on the original container. Pour a small amount in a separate container, use as desired, and dispose of the excess. Do NOT pour wax back into the original container. If the wax has a strong, sour odor, it has been contaminated. Clean up is easy with warm, soapy water. 1. Trail or brush Black Wax Resist in desired pattern and allow to dry a minimum of 2 hours. 2. Apply glaze or slip by dipping or brushing. 3. Fire (cone 06-8). Results may vary - please test first. Please Note: The Wax will FREEZE in cold climates and will not resist effectively. If the wax has frozen, it will get lumpy and separate. Wax Resist will be sent to cold regions in the winter only at the customer's risk.
SHIMPO’s banding wheels are used for decorating, sculpting, carving and hand building. Designed to provide reliably smooth and even rotation for the most delicate applications. It's no wonder they are the banding wheel of choice for studio artists, production potters and classrooms alike. In five different models, we offer a selection of wheel-head diameters and heights. Banding Wheels Solid Cast-iron Construction Heavy-duty construction ensures many years of use and will hold a spin and stay in place as needed Sealed Ball Bearings Extra smooth and even rotation (no wobbling or sticking) One-piece Design Will not come apart when lifted Top Grade Paint Coating Rust-resistant Warranty 1-year
Model
BW-30M
BW-25H
BW-25L
BW-22L
BW-18L
Diameter 11 ¾" 9 7/8" 9 7/8" 8 ¾" 7" Height 4 ¾" 7 ½ 2 ¼" 2 ¼" 2 ¼" Ship Weight 28 lbs. 19 lbs. 15 lbs. 13 lbs. 6.50 lbs.
Water based wax emulsion used for glaze decorating. Glaze will be resisted where wax is applied. Dries quickly on bisque and in a consistency favorable to brush work. Please Note: The Wax will FREEZE in cold climates and will not resist effectively. If the wax has frozen, it will get lumpy and separate. Wax Resist will be sent to cold regions in the winter only at the customer's risk.
This white paste is an excellent mending material for bisque that can be used to bond pieces together or fill up broken cavities. Bisque Fix can be colored to match the bisque using metal oxides or ceramic stains. After applying with a spatula, fire to the temperature of the clay and glaze that you are using -- up to Cone 10 (2381°F, 1305°C). Important Storage Note:Bisque fix is and air set concrete type product. There is a way to keep it longer. After you have used it and are ready to put it away, put a thin layer of water in the jar then recap and store. When you go to use it again pour off the water, remix and apply as normal.
