Welcome to our new site. We hope you enjoy it. We are in our final testing to make sure everything is ready for you to come and SHOP. Look around all you like, we'll be officially open over here 12/26/24!
Hold loose kiln elements in place with these easy to insert pins. These 1-1/4" pins are of a heat resistant alloy for temperatures to 2500 degree F (Cone 13). Sold 12 per package.
Type K thermocouples are the most common type of thermocouples used in electric kilns. These thermocouples are purchased in bulk directly from the factory to save you money. The manufacturer is ISO/IEC 17025 certified.
Original factory 8 Gauge Type K thermocouple replacement WITH MOUNTING BLOCK. Typically, you'd only need the thermocouple (thermocouple alone is Skutt part 1515) unless the mounting block has been damaged in some way. Skutt part number 1506.
One of David Sturm's top 5 favorites! The Dual Input Digital Pyrometer offered by Skutt is of very high quality. It comes with 1 thermocouple but if you purchase an additional one, this pyrometer has the ability to read multiple zones at one time. The digital readout is easy to read and extremely accurate. It can be wall mounted or hand held. It also has a convenient flip out stand so you can set it upright on a flat surface. It comes with the following items: 1 – 2350 F (1285 C) Pyrometer with mounting case 1 – 6ft Type K thermocouple wire with 8″, 8 gauge, Type K Thermocouple 1 – Thermocouple mounting flange with mounting screws 1 – 9 volt battery included
25 Amp Relay for KM Skutt kiln models Also called an Ice Cube Relay or a 25 Amp Detrol relay. If you aren't sure which relay you need, count the number of vent slots (louvers) on the top of your control box. If they have 5 slots, use this relay. This also applies if you've done the relay upgrade kit. If you are unsure about which relay you need, please contact David by phone (1-888-822-1982) or email him.
25 Amp relay for newer model or upgraded KM kilns. Also referred to as the Potter & Brumfeld relay
If you aren't sure which relay you need, count the number of vent slots (louvers) on the top of your control box. If they have 6 slots, use this relay. This also applies if you've done the relay upgrade kit, even if the control box only has 5 vent slots.
Elements for all current model Skutt Kilns (8-12 sided, KM and KMT only, non PK), includes 818, 822, 1018, 1022, 1027, 1218, 1222, 1227
Kiln element stock varies wildly. If your elements are not in stock here, we will have them shipped to you from the manufacturer.
Looking for elements for a different Skutt kiln? Scroll down to see other options.
Check out this video of Dave showing how to pin elements.
Elements for all current model Skutt PK Kilns (includes 1227-3PK, 1231-3PK, 1427-3PK, and 1627-3PK)
Kiln element stock varies wildly. If your elements are not in stock here, we will have them shipped to you from the manufacturer.
Looking for elements for a different Skutt kiln? Scroll down to see other options.
Check out this video of Dave showing how to pin elements.
The Easy View is a simple wedge shaped piece of powder coated sheet metal that simply angles the touch pad out so it is easy to see and program. It is especially helpful to people who own older Skutt models that had the touch pad located near the bottom of the control box. It is very easy to install without have to disconnect any wires. One size fits all full size KilnMaster or GlassMaster control box.They are inexpensive and can make programming much easier. you can also order it with a LinkBoard to upgrade your kiln with KilnLink or to plug in an EnviroLink. If you are ordering a new kiln with KilnLink you will need 1 LinkBoard per kiln and one KilnLink Box to run up to 4 kilns. You will also need to purchase 1 Service Plan. A LinkBoard with EasyView is required for upgrading existing kilns. Easy View Installation
Elements for all smaller, current model, KM or KMT Skutt kilns (includes Firebox 8x4 LT, 8x6 LT, Glazetech, 614-3, and 714)
Kiln element stock varies wildly. If your elements are not in stock here, we will have them shipped to you from the manufacturer.
Looking for elements for a different Skutt kiln? Scroll down to see other options.
Check out this video of Dave showing how to pin elements.
