Skutt Ceramic Products Skutt EV2 Rolling Stand Adapter
Have a Rolling Stand? Have an EnviroVent2? You may want to purchase the new EV2 Rolling Stand Adapter. The new adapter is a bracket that is designed to fit in between the cross supports of your Skutt Rolling Kiln Stand. The EnviroVent2 collection cup is spring loaded so it can move up and down with the bottom of the kiln as the brick expands and contracts. With the new bracket, the foot of the collection cup is spring loaded against the bracket instead of the floor. This way, when you roll your kiln, the cup goes with it. Now obviously you can't roll it very far because it it is attached with ducting to the motor, but it does allow you to move it for cleaning without having to reposition the cup. KILN VENTING FAQs Q.Why is room air venting important to people?A. Kiln manufacturers have always recommended that firing areas have adequate ventilation. There are many reasons why kiln venting stressed more now. Today's environmental consciousness has created more awareness of potential health hazards. Studies have shown that carbon monoxide emissions can exceed OSHA Threshold Limit Values during bisque firing of electric kilns. Formaldehyde and sulfur dioxide also may be present in lower concentrations. Because of these concerns, kiln venting is required by building code in most areas. Q.Why is internal kiln venting important to my ware?A. Ceramic and glass fusing materials, including greenware, glazes and lusters, contain organic compounds. The first phase of the firing process removes these gases or vapors from the ware before the higher temperature changes take place. These contaminants need to be removed from the kiln, and replaced with fresh air. This is especially important with red, orange, yellow and brown glazes and lusters, because they need oxygen for good results. Some specific problems related to poor venting include: Grayish inner areas (black core) when bisque firing earthenware. Unburned carbon in bisque ware that causes crazing, pinholes or blisters during glaze firing. Dulled surfaces and cloudy colors caused by sulfur gases. Weak colors in red-orange-yellow glazes. Color migration caused by glaze fumes depositing on nearby ware. Cones which fall improperly due to inadequate oxygen. If your firing chamber is not properly vented, your work is likely to suffer. Q.Can you describe my kiln venting options? A. There are several options, ranked here in order of sophistication: Natural ventilation from open doors and windows. Room ventilation fans. Convection canopy collection hoods. Mechanical fan collection hoods. Mechanical downdraft vent systems. Q.What are the main differences between venting systems? A. Window ventilation and convection hoods are passive—the warm fumes rise, and hopefully, are diluted or escape. This requires very large volumes of fresh air, which is costly in the winter. Collection hoods with electric fans do a better job of removing fumes, but fumes still enter the room air before they are collected. There is usually still a significant odor. External hoods do not help internal kiln performance. Mechanical downdraft systems, such as the Skutt EnviroVent, were developed to address both needs: Improved kiln firing chamber heat distribution and circulation for more consistent firing results; and Removal of fumes directly from the firing chamber before they can post a health hazard. Little or no odor can be detected. Q. How much does heat distribution vary?A. A one-cone difference is common from top to bottom of an unvented kiln. You can observe this difference with cone groups set at different levels. The difference can grow great with larger electric kilns, especially when firing to low temperatures. For example, cone 03 has bent on a top shelf when only cone 05 has bent on a bottom shelf. Tests have shown a 30° difference top to bottom on high fires and 80° difference when low firing. Q. How much does the EnviroVent help heat distribution? A. Heat naturally rises therefore the bottom of the kiln can fire cooler than the top, especially at lower temperature ranges. On tests conducted on a 10 cu. ft. kiln with pyrometers at six levels, it was found that the EnviroVent can cut temperature differences to about half of normal. The top-to-bottom differential was cut from 79° to 45°. Some users have reported even greater improvement in heat distribution. Q. How does it work? A. Developed jointly with the Edward Orton Jr. Ceramic Foundation, the EnviroVent is protected under U.S. patent 4,863,374. It is unique because it creates a downdraft venting effect, immediately mixing fumes with cooling air in a closed plenum chamber at the bottom of the kiln. The venting requires a few very small holes to be drilled in the lid and floor of the kiln . The fan motor mounts to the wall and vents the fumes to the outside much like a household dryer. Q. Does this require major Modifications to my kiln? A. No. You can use the twist drills we provide to bore though the soft firebrick by hand. The holes are quite small, shown here at actual size. As an example, the Skutt 1018 needs only two 15/64” holes in the floor and lid. We can pre-drill the kiln in the factory at the time it is ordered. Be sure to tell your distributor when ordering your new kiln that you want it drilled. Q. Is installation difficult? A. No. You drill the few holes needed for your kiln, place the EnviroVent 2 spring loaded plenum cup under your kiln and mount the motor to the wall. We supply the aluminum drier ducting that is used between the plenum cup and the motor. Skutt even supplies the stainless sleeve that is needed to pass through the wall. It runs on 115V household current. If you install the EnviroVent on a kiln with a metal floor plate, you will need an electric drill. Q. Must I always turn on the EnviroVent when I fire? A. Yes. The airflow is necessary to cool the EnviroVent's electric motor. However, you will want to use the EnviroVent for all types of firings in any case. Q. Can I do burn-out firings? A. The EnviroVent was designed for conventional pottery techniques. A large load of burn-out pieces may momentarily overload the EnviroVent. We recommend smaller loads of burn-out pieces. Q. Can I rearrange my kiln area easily? A. Certainly, The vented air is cool enough to allow you to use flexible ducting away from the kiln. There are no overhead brackets or pulleys to restrict -your locations. Q. Does the EnviroVent change firing times? A. There may be a slight increase of 10 to 15 minutes to shut-off in an 8 hour firing. However, your total kiln firing cycle will probably be shorter because the EnviroVent removes heat from the kiln after shut-off without causing thermal shock. Q. What does the UL listing of a kiln vent system mean?A. It means that the manufacturer has submitted the vent unit, properly installed on specific kiln models, to Underwriters' Laboratories for rigorous testing under actual high-heat firing conditions. When installed on Skutt UL kilns, the EnviroVent is the only UL listed downdraft vent system. Some kiln vents use an electric motor which may have been UL listed for general room temperature use. This does not make their vents UL listed. Q. What is The EnviroLink?A. The EnviroLink is an accessory item that can be ordered for the EnviroVent and Envirovent 2 that works in conjunction with the Skutt KilnMaster or GlassMaster controller. It allows you to program the controller to automatically turn the vent on and off throughout a firing program. You simply enter an on/off setting for each segment of a Ramp and Hold program while you are programming the kiln. There are preset “vent programs” that can be run in conjunction with a ConeFire Mode or GlassFire Mode program as well.
$33.00
Cone Art Kilns by Tucker's Furniture Kit for Cone Art B3K119
Includes: one 10" diameter round kiln shelf three 1" kiln posts three 2" kiln posts two kilograms kiln wash image shown only indicates that it's a furniture kit and does not show the actual contents of this particular furniture kit
$39.55
Skutt Ceramic Products Skutt 1218-3
This 12 sided Skutt kiln has a 28" interior diameter and is 18" inches deep. The chamber size is tall enough to fire a 14″ tall pot and wide enough to hold a 26″ platter. Downloadable Spec Sheets: (KM or KMT) 1218-3 • 1 Phase 240 Volts 1218-3 • 3 Phase 240 Volts 1218-3 • 1 Phase 208 Volts 1218-3 • 3 Phase 208 Volts
$4,275.00 - $4,702.50
Cone Art Kilns by Tucker's Cone Art 1813D
Overview 1.7 Cubic Feet Double Wall Insulation Kanthal A-1 Elements 208 or 240 Volts 30 Amp Breaker Required Bartlett or Genesis Touchscreen Controller The Tuckers Cone Art model 1813D is a very versatile kiln. It is used in doll studios, the pottery studios and classrooms. It fires easily to a true cone 10. It is a double insulated kiln with 2.5 ” premium brick plus 1″ of block insulation. This double insulation saves approximately 30% in electricity costs and has a safer, cooler jacket. Kanthal A-1 elements, stainless steel jacket and fittings, and excellent Cone Art craftsmanship all are standard. The Bartlett electronic controller is mounted in an angled, easy view control panel for precise control. This kiln is available with either the standard V6-CF keypad or the new Genesis touch screen. The standard model is the BX1813D. The Genesis version is GX1813D. The Tuckers Cone Art Model 1813D is an excellent choice if you want the best cone 10 kiln built today.
$3,280.50 - $3,600.00
Skutt Ceramic Products Skutt Rolling Kiln Stand for 8-sided kiln
Almost every kiln that Skutt sells comes with a stand but most of them are designed to stay put. Trying to move them with the kiln setting on them could result in a broken stand or even worse a broken kiln, or even worse, a broken you. Often times you may want to move your kiln to clean under it or just get it out of the way when it is not being used. Think how nice it would be to get that car in the garage every once in a while. Our rolling stands are constructed out of heavy duty, welded square tubing and fitted with high quality, locking steel castors ont models designed for large kilns. Steel castors will not develop flat spots if they sit too long in one spot unlike rubber or plastic wheels. They provide the recommended clearances from the kiln to the floor and many are adjustable in order to raise the loading level to a height that is comfortable for you. This stand will position your kiln base 8" above the floor and is NOT adjustable.
$396.00
The Ceramic Shop D Series Stilt #4B: 4 in. long with 10 pins
We like these stilts because of their versatility. You can combine different sizes to accommodate almost any pot that you wish to fire. And because of the multiple metal points, these stilts can handle heavy pieces. The Series D #5B stilt is 3.25" in length and has 9 metal points All the silts are rated to cone 10.
$2.40
Skutt Ceramic Products Skutt Rolling Kiln Stand for 10-sided kiln
Almost every kiln that Skutt sells comes with a stand but most of them are designed to stay put. Trying to move them with the kiln setting on them could result in a broken stand or even worse a broken kiln, or even worse, a broken you. Often times you may want to move your kiln to clean under it or just get it out of the way when it is not being used. Think how nice it would be to get that car in the garage every once in a while. Our rolling stands are constructed out of heavy duty, welded square tubing and fitted with high quality, locking steel castors ont models designed for large kilns. Steel castors will not develop flat spots if they sit too long in one spot unlike rubber or plastic wheels. They provide the recommended clearances from the kiln to the floor and many are adjustable in order to raise the loading level to a height that is comfortable for you. This stand will position your kiln base 8" above the floor and is NOT adjustable.
$450.00
Cone Art Kilns by Tucker's Cone Art 4227D Oval Kiln
The Tuckers Cone Art Kiln Model 4227D is a massive 16.5 cubic feet oval kiln with a full 42" width, 31" from front to back and a 27" depth. The 4227D is designed for a busy production or sculpture studio. It is a double insulated kiln with 2.5 " of premium firebrick plus 1" of block insulation around the walls. The floor and lid are constructed with 3" firebrick and has an additional 1" of block insulation. The entire kiln, including the lid, is clad in a stainless steel jacket for extra protection and durability. The extra insulation ensures even firings, stops heat loss through the walls and lid, saves 30% in electricity costs, and lengthens element life. There are heavy-duty Kanthal A-1 elements in the walls and floor. This kiln makes firing up to cone 10 effortless even with heavy loads. The kiln is equipped with a Bartlett Controller with 3 Zone Control at NO EXTRA CHARGE which is mounted on an angled easy view panel. The Tuckers Cone Art Kiln Model 4227D also comes with our patented LID LIFTER at NO EXTRA CHARGE. The 4227D has all the features and more that you need in a professional kiln. Three-zone control with the Bartlett electronic controller comes at NO EXTRA CHARGE so the kiln will fire perfectly time after time. Now, also a standard feature, the Cone Art Lid Lifter at NO EXTRA CHARGE. Lift the lid with one finger! There is no kiln on the Market today that has as many excellent features at such a good price as the Tuckers Cone Art BX2327D.
$9,117.00 - $9,436.50
Bracker's Good Earth Clays Bracker's Post Assortment
The staff at Bracker's think we can put together a post assortment based on our own experiences as well as the knowledge we've gleaned from our customers throughout the years. So here's what we've come up with, based on using 3 posts per shelf (either half or full): Includes 1-1/2" square posts in the following heights: 10 - 1" posts great for supporting the bottom shelf as well as stacking with another post for a little extra space 6 - 2" square posts for very small items, tiles, or for stacking with another post for extra space 12 - 4" square posts a very useful size for smaller projects 12 - 6" square posts a very popular and useful post height for most people 12 - 8" square posts place tall pots on the top shelf in the kiln, but when that isn't enough, these posts will help 1 pair Leather Welder's Kiln Gloves *These posts are safe to fire all the way up to cone 10!
$220.00
Skutt Ceramic Products Skutt Rolling Kiln Stand for 12-sided kiln
Almost every kiln that Skutt sells comes with a stand but most of them are designed to stay put. Trying to move them with the kiln setting on them could result in a broken stand or even worse a broken kiln, or even worse, a broken you. Often times you may want to move your kiln to clean under it or just get it out of the way when it is not being used. Think how nice it would be to get that car in the garage every once in a while. Our rolling stands are constructed out of heavy duty, welded square tubing and fitted with high quality, locking steel castors ont models designed for large kilns. Steel castors will not develop flat spots if they sit too long in one spot unlike rubber or plastic wheels. They provide the recommended clearances from the kiln to the floor and many are adjustable in order to raise the loading level to a height that is comfortable for you. This stand will position your kiln base 8" above the floor and is NOT adjustable.
$395.00
The Ceramic Shop E Series Stilt E2S: 1-3/4 in. tall inner support rod
We like these stilts because of their versatility. You can combine different sizes to accommodate almost any pot that you wish to fire. And because of the multiple metal points, these stilts can handle heavy pieces. The Series E #2S stilt measures 1.25" from the tip of one arm to the tip of the next. Each arm has 3 metal points, for a total of 9. The length of inner metal rod measures 1.75". All the silts are rated to cone 10.
$2.50
The Ceramic Shop F Series Stilt F3H: 1-1/2 in. high with 1-1/4 in. between pins
We like these stilts because of their versatility. You can combine different sizes to accommodate almost any pot that you wish to fire. And because of the multiple metal points, these stilts can handle heavy pieces. The Series F #3H stilt is 1.5" in height and measures 1.25" from point to point. All the silts are rated to cone 10.
$1.85
Skutt Ceramic Products Skutt Easy View
The Easy View is a simple wedge shaped piece of powder coated sheet metal that simply angles the touch pad out so it is easy to see and program. It is especially helpful to people who own older Skutt models that had the touch pad located near the bottom of the control box. It is very easy to install without have to disconnect any wires. One size fits all full size KilnMaster or GlassMaster control box.They are inexpensive and can make programming much easier. you can also order it with a LinkBoard to upgrade your kiln with KilnLink or to plug in an EnviroLink. If you are ordering a new kiln with KilnLink you will need 1 LinkBoard per kiln and one KilnLink Box to run up to 4 kilns. You will also need to purchase 1 Service Plan. A LinkBoard with EasyView is required for upgrading existing kilns. Easy View Installation
$40.00
Skutt Ceramic Products Skutt 1222-3
This 12 sided Skutt kiln has a 28" interior diameter and is 22" inches deep. The chamber size is tall enough to fire a 18″ tall pot and wide enough to hold a 26″ platter. Downloadable Spec Sheets: (KM or KMT) 1222 • 1 Phase 240 Volts 1222 • 1 Phase 208 Volts 1222 • 3 Phase 240 Volts 1222 • 3 Phase 208 Volts
$4,608.00 - $5,035.50
Skutt Ceramic Products Skutt Element Pins, package of 12
Hold loose kiln elements in place with these easy to insert pins. These 1-1/4" pins are of a heat resistant alloy for temperatures to 2500 degree F (Cone 13). Sold 12 per package.
$6.00
Kemper Tools Kemper ELS Element Staples - hairpin shaped
Hold loose kiln elements in place with these easy to insert, sharp-ended staples. These 1-1/2" staples are of a hear resistant alloy for temperatures to 2500 degree F (Cone 13). Packed 12 per package.
$6.99
Cone Art Kilns by Tucker's Furniture Kit for ConeArt BK2327D-SQ
image shown only indicates that it's a furniture kit and does not show the actual contents of this particular furniture kit This is high alumina kiln furniture that is rated to cone 11. INCLUDES: Three 21" x 23" x 3/4" full square shelves Two 21" x 10-1/2" x 3/4" half square shelves Three each 1", 2", 6", and 8" posts Six 4" posts All posts are 1-3/4" square Two kilograms kiln wash
$425.00
Cone Art Kilns by Tucker's Furniture Kit for ConeArt BK2336D
image shown only indicates that it's a furniture kit and does not show the actual contents of this particular furniture kit This is high alumina kiln furniture that is rated to cone 11. INCLUDES: Three 21" x 10-1/2" x 3/4" half square shelves Six 21" x 3/4" half round shelves Nine each 1", 2", 4, 6", and 8" posts All posts are 1-3/4" square Two kilograms kiln wash
$525.00
Cone Art Kilns by Tucker's Furniture Kit for ConeArt BK4227D
image shown only indicates that it's a furniture kit and does not show the actual contents of this particular furniture kit This is high alumina kiln furniture that is rated to cone 11. INCLUDES: Three 26" x 13" x 3/4" half square shelves Six 26" x 3/4" half round shelves Nine each 1", 2", 4, 6", and 8" posts All posts are 1-3/4" square Two kilograms kiln wash
$705.00
Skutt Ceramic Products Furniture Kit for Skutt KM614-3
[image is representative of Skutt furniture kits in general and does not reflect the actual items in this kit]INCLUDES: 1 - 9.25" x 10" full shelf (1/2" thick) 1 - 9.25" x 5" half shelf (1/2" thick) 3 each - 1", 2", 3", 4", 5", and 6" posts 8 oz. kiln wash
$170.00
Cone Art Kilns by Tucker's Cone Art 2336D Oval Kiln
The Cone Art Kilns Model 2336D is a large 12 cubic foot oval kiln with a full 36" width. It has been designed especially for the busy production artist and sculptor studio that need the extra width. It is a double insulated kiln with a wall profile of 2.5 " premium firebrick plus 1" of block insulation. The extra insulation ensures a cooler, safer jacket, longer element life, and approximately 30% savings in electricity costs. The kiln is clad in a stainless steel jacket for extra protection and durability. There are heavy-duty Kanthal A-1 elements in the walls and floor. This makes firing to cone 10 a breeze even with high mass loads. This kiln is equipped with a counter weight lid lifter and Bartlett electronic controller with 3 Zone Control panel mounted on an angle for easy viewing. Both features come standard at NO EXTRA CHARGE. There is no other kiln that can match the Tuckers Cone Art Kilns feature for feature. Three-zone control with the Bartlett electronic controller comes at NO EXTRA CHARGE so the kiln will fire perfectly time after time. Now, also a standard feature, the Cone Art Lid Lifter at NO EXTRA CHARGE. Lift the lid with one finger! There is no kiln on the Market today that has as many excellent features at such a good price as the Tuckers Cone Art 2327D.
$7,393.50 - $7,713.00
Skutt Ceramic Products Furniture Kit for Skutt KM714
[image is representative of Skutt furniture kits in general and does not reflect the actual items in this kit]INCLUDES: 1 - 13" full shelf (5/8" thick) 1 - 6.5" x 13" half shelf (5/8" thick) 3 each - 1", 2", 3", 4", 5", and 6" posts 8 oz. kiln wash
$195.00
Skutt Ceramic Products Skutt 25 Amp Relay - 5 Slot Box
25 Amp Relay for KM Skutt kiln models Also called an Ice Cube Relay or a 25 Amp Detrol relay. If you aren't sure which relay you need, count the number of vent slots (louvers) on the top of your control box. If they have 5 slots, use this relay. This also applies if you've done the relay upgrade kit. If you are unsure about which relay you need, please contact David by phone (1-888-822-1982) or email him.
$46.00
Skutt Ceramic Products Skutt 25 Amp Relay - 6 Slot Box
25 Amp relay for newer model or upgraded KM kilns. Also referred to as the Potter & Brumfeld relay If you aren't sure which relay you need, count the number of vent slots (louvers) on the top of your control box. If they have 6 slots, use this relay. This also applies if you've done the relay upgrade kit, even if the control box only has 5 vent slots.
$40.00
I18n Error: Missing interpolation value "number1" for "You have seen {{ number1 }} out of {{ number2 }} products"