Basic Glazing Instructions
First you want to apply wax resist to the foot of your pot (where you don't want any glaze). When you dip your pot in bucket of glaze, the glaze won't stick where you have waxed. The glazes become molten glass in the kiln, so if there is any glaze on the bottom, your pot will stick to the shelf. This will wreck your pot and your kiln shelves! Paint a thin coat of wax on the bottom, as well as up the sides at least ¼ inch. All glazes move a little in the firing, and some are quite runny. Always leave enough room for your glaze to flow some without sticking to the kiln shelf. Until you are familiar with a particular glaze, it is better to leave some extra room.

Use a thin coat of wax. It works better and dries faster.
Let the wax dry for at least 15 or 20 minutes before dipping a pot in glaze.
Use an old cruddy brush, they are never the same after using for wax.
Clean your wax brush in warm water with a drop or two of dishwashing soap.
Be careful not to get the wax where you don't want it, i.e. waxy fingerprints.
Before you glaze your work, you should quickly rinse it under cold water.
Thoroughly mix the glaze just before you use it.

Dipping
To coat the whole piece in a single glaze, the easiest technique is to pick it up with a pair of glaze tongs, dip it in, count to three and pull it out. Make sure to empty it as you withdraw it. If you pull a bowl out still full of glaze it will weigh so much that the tongs will break through. Hold it upside down over the bucket to drain the excess glaze. There will probably be some glaze sticking to the waxed areas; wipe off what you can while you are holding it with the tongs. Set the piece down and let it dry. After it is dry enough to handle, turn it over and sponge off any glaze still remaining on the bottom. The foot must be perfectly clean before it can go in a kiln.

Brushing
For brushing, most glazes need 2 to 3 coats. It is easier to get even coverage if you brush the first coat side to side, then the next coat up and down.

Firing
These glazes work best when fired between cone 5 and 6 (Orton Standard or Self-Supporting Cones, used as a witness cone placed on the kiln shelf during firing). If you use a kiln sitter you usually have to use a cone six in the sitter to achieve a good cone 5. For automatic kilns, we fire to cone 5 (fast) with a 15 minute hold. Every kiln is different, so you may have to fine tune your firing to achieve the best results.

Country/region

Most popular clays

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

AMACO

Coyote

Laguna

Mayco

Opulence

Spectrum

Western Glazes

Underglazes & other color

UG Transfers

Mason Stains®

Overglazes

Trending tools

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

New! Colored Grog!!!

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

New! Colored Grog!!!

Archie's Glazes

Copper & Iron

Constellations

Crawl

Enduro Glazes

Fantasy

Gloss

Shino

Satin

Frank's

Matt

Mottled

Slow Cool

Texas Two Step

Vibro-Colors

Collection: All Coyote Glazes

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Choose your option

Resources

Jump to:

send a message

e-mail us

Visit in Lawrence KS

Call Us

Your cart