INCLUDES: DS13A - 3"x1 5/8" Flared Tray DS13B -3 1/4"x1 7/8" Flared Tray DS13C - 3 1/2"x2 1/8" Flared Tray The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
The Stainless Steel Work Shelf has safety rounded edges, is easy to clean and maintains a flawless surface with proper care-protecting your reclaimed over spray from contamination with wood chips or rust flakes.
4" Expansion Box Slab Die Kit for 4" Extruders. Cast aluminum expansion box die kit for slabs. It will produce a 6" diameter round tube with a wall thickness of 3/8" or 1/2". To layout an 18" slab, cut tube down one side of the tube. Use of this Die Kit requires the 4" Aluminum Expansion Box. Made in the U.S.A.
4" Expansion Box Wooden Dit Kit for 4" Extruders. Marine grade plywood inner and outer dies to make circle, square, and hexagonal shapes. Extrusion wall thickness 1/2". The Wooden Dies will produce 6" diameter extrusions. Use of this Die Kit requires the 4" Aluminum Expansion Box. Made in the U.S.A.
The Jumbo Platter extender attaches onto all standard Giffin Grips, creating a 24" platter for trimming large pots. The Jumbo Platter Extender™ is an accessory to the Giffin Grip®.
The Stainless Steel Work Shelf has safety rounded edges, is easy to clean and maintains a flawless surface with proper care-protecting your reclaimed over spray from contamination with wood chips or rust flakes.
The adjustable leg stool allows an assortment of heights to accommodate everyone, and can be tilted to relieve strain on your lower back. The tilt feature also puts you over your work to help you while centering on the wheel. The stool is finished attractively with a white frame and blue seat. The adjustable leg stool not only serves the potter but will also comfortably fill the needs of the painter and sculptor.
SPECIFICATIONS Adjustable Legs Adjustable leg heights: 19" - 26" with a tilt seat feature Adjustable Slots Nine adjustable slots in 1" increments Cushioned Seat Padded comfort Warranty 2years Dowload Product Info Shimpo Adjustable Stool PDF
INCLUDES: DS12A - 2"x1 1/4" Tray DS12B -2 1/2"x1 1/2" Tray DS12C - 3"x2" Tray The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS11A - 2"x2" Tray DS11B -2 1/2"x2 1/2" Tray DS11C - 3"x3" Tray The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS9A - 1" Handle DS9B -1 1/2" Handle DS9C - 2" Handle The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: DS4A - 1 1/2" Hollow Heart DS4B - 2" Hollow Heart DS4C - 2 1/2" Hollow Heart DS4D - 1 1/4" Hollow Diamond DS4E - 2" Hollow Diamond DS4F - 2 1/2" Hollow Diamond The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
INCLUDES: (1) WA (1) WA Board (1) Round 5" (1) Round 6.5" (1) Round 8" (1) Round 9.5" (1) Round 11 (4) WA Spacers (total) All forms measured in inches. Accessory to attach on the top of a potter's wheel to create (round) plates.
Create 8" square (or with lip 10 1/4" square) dishes easily. This mold actually has a total size of 10 1/4" square, with the inner slump an 8" square. The inner bottom flat is approximately 4 5/8" square with a depth of 5/8". You can trim the clay to the 8" square, or add a "lip" to your dish and trim at the 10 1/4" square. Allow clay slab to dry in the mold before removing from mold and firing.
INCLUDES: DS1A - 1 1/2" Hollow Octagon DS1B - 2" Hollow Octagon DS1C - 2 1/2" Hollow Octagon DS1D - 1 1/2" Hollow Star DS1E - 2" Hollow Star DS1F - 2 1/2" Hollow Star The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
