Welcome to our new site. We hope you enjoy it. We are in our final testing to make sure everything is ready for you to come and SHOP. Look around all you like, we'll be officially open over here 12/26/24!

MAGMA - Miracle Anti-Gravity Multipurpose Additive

Description

MAGMA - Miracle Anti-Gravity Multipurpose Additive

No more hard settled glazes, no more powdery glaze coatings, no more peeling glazes.

All your suspension and application problems solved!

  • Suspends ANY common glaze material, including dense granular materials, indefinitely.
  • Works with or without clay - even zero clay formulations.
  • Allows glaze carving and sgraffito without chipping.
  • Allows unlimited layering of glaze or slip coats.
  • Hardens unfired glaze and slip coatings.
  • Does not change with age (requires preservative*).
  • Does NOT deflucculate and cause curtaining and drips like CMC does.
  • Almost completely burns away, leaving fired glaze or slip unaffected.
  • For brush application, smooths application and hardens the coat like CMC but allows heavier brush loading and thicker coats than CMC.


GLAZE/SLIP TYPE 100g batch (brushing) 100g
batch
1000g batch 10,000g batch
zero clay formula 0.7g 0.6g 6g 60g
typical formula
(10% clay)
0.6g 0.4g 4g 40g
high clay formula 0.5g 0.3g 3g 30
For brushing glazes, increase recommendations by 0.1%.
As a clay plasticizer, try 0.1% MAGMA.


Two simple ways to add it to your slip or glaze:

LIQUID GLAZE

  1. Add 40 grams MAGMA and 4 grams Copper Carbonate (CuCO3) to 8 ounces hot water.
  2. Wait approximately 6 hours. It will look like green goop.
  3. Add a little MAGMA gel to your liquid glaze - start with 1 teaspoon of MAGMA gel per pint of glaze. You can always add a more if you need it, but it’s better to err on the side of caution because MAGMA increases the drying time of the glaze.

DRY GLAZE

  1. Determine appropriate quantity of MAGMA.
  2. Mix MAGMA powder with other dry ingredients. Add 0.04% (of total batch weight) Copper Carbonate (CuCO3) as a preservative unless Copper Carb is already included in the recipe. Example: 0.4g CuCO3 per 1000g dry glaze
  3. Add dry mix to normal amount of [hot] water for glaze batch. Glaze will be a little thicker than you are used to.
  4. Wait a few hours before sieving.

Always glaze the outside surface first when using a glaze with MAGMA or any other additive.

Recommended preservative: If you plan to store glaze mixed with water for more than one week, add Copper Carbonate (CuCO3), 0.04% of total dry batch (0.4g CuCO3 per 1000g dry glaze). The vast majority of glazes will not show any coloration from this small amount of copper, but it will prevent the gum from rotting. Test before mixing a full batch.

CAUTION:

MAGMA will dramatically thicken any glaze it is added to. Thinning the glaze to a “normal” consistency will cause very thin coats. MAGMA containing glazes must have more viscosity than typical glazes. MAGMA glazes also take more time to “dry” (the water moves into the bisque slower) after dipping or spraying. If high viscosity glazes will not work for you, and/or slow setting or drying glazes will not work for you, you should not use MAGMA.

Product form

downloadable information sheet No more hard settled glazes, no more powdery glaze coatings, no more peeling glazes. All your suspension... Read more

Free pickup in our shop(s)

SKU: MATMAGMA100

$6.00

6 in stock

    Description

    MAGMA - Miracle Anti-Gravity Multipurpose Additive

    No more hard settled glazes, no more powdery glaze coatings, no more peeling glazes.

    All your suspension and application problems solved!

    • Suspends ANY common glaze material, including dense granular materials, indefinitely.
    • Works with or without clay - even zero clay formulations.
    • Allows glaze carving and sgraffito without chipping.
    • Allows unlimited layering of glaze or slip coats.
    • Hardens unfired glaze and slip coatings.
    • Does not change with age (requires preservative*).
    • Does NOT deflucculate and cause curtaining and drips like CMC does.
    • Almost completely burns away, leaving fired glaze or slip unaffected.
    • For brush application, smooths application and hardens the coat like CMC but allows heavier brush loading and thicker coats than CMC.


    GLAZE/SLIP TYPE 100g batch (brushing) 100g
    batch
    1000g batch 10,000g batch
    zero clay formula 0.7g 0.6g 6g 60g
    typical formula
    (10% clay)
    0.6g 0.4g 4g 40g
    high clay formula 0.5g 0.3g 3g 30
    For brushing glazes, increase recommendations by 0.1%.
    As a clay plasticizer, try 0.1% MAGMA.


    Two simple ways to add it to your slip or glaze:

    LIQUID GLAZE

    1. Add 40 grams MAGMA and 4 grams Copper Carbonate (CuCO3) to 8 ounces hot water.
    2. Wait approximately 6 hours. It will look like green goop.
    3. Add a little MAGMA gel to your liquid glaze - start with 1 teaspoon of MAGMA gel per pint of glaze. You can always add a more if you need it, but it’s better to err on the side of caution because MAGMA increases the drying time of the glaze.

    DRY GLAZE

    1. Determine appropriate quantity of MAGMA.
    2. Mix MAGMA powder with other dry ingredients. Add 0.04% (of total batch weight) Copper Carbonate (CuCO3) as a preservative unless Copper Carb is already included in the recipe. Example: 0.4g CuCO3 per 1000g dry glaze
    3. Add dry mix to normal amount of [hot] water for glaze batch. Glaze will be a little thicker than you are used to.
    4. Wait a few hours before sieving.

    Always glaze the outside surface first when using a glaze with MAGMA or any other additive.

    Recommended preservative: If you plan to store glaze mixed with water for more than one week, add Copper Carbonate (CuCO3), 0.04% of total dry batch (0.4g CuCO3 per 1000g dry glaze). The vast majority of glazes will not show any coloration from this small amount of copper, but it will prevent the gum from rotting. Test before mixing a full batch.

    CAUTION:

    MAGMA will dramatically thicken any glaze it is added to. Thinning the glaze to a “normal” consistency will cause very thin coats. MAGMA containing glazes must have more viscosity than typical glazes. MAGMA glazes also take more time to “dry” (the water moves into the bisque slower) after dipping or spraying. If high viscosity glazes will not work for you, and/or slow setting or drying glazes will not work for you, you should not use MAGMA.

    Resources

    Recently viewed products

    © 2024 Brackers Good Earth Clays, Powered by Shopify

      • American Express
      • Apple Pay
      • Diners Club
      • Discover
      • Google Pay
      • Mastercard
      • PayPal
      • Shop Pay
      • Venmo
      • Visa

      Login

      Forgot your password?

      Don't have an account yet?
      Create account