Welcome to our new site. You are now welcome to shop and place your orders here. Use your email address to login. You will receive a confirmation code via email to checkout
CSI Turntables are made of two plastic laminate covered particle boards (plastic laminate design will vary from one to the other) with a stainless steel ball bearing, screwed into the inside surfaces of the boards. The 8" & 10" turntables have a 4" bearing capable of supporting at least 200# and the 12", 14" & 16" have a 6" bearing capable of supporting at least 300#. To clean, wipe with a damp sponge (do not submerge the turntable in water).
Each Wallie Casserole Form has a 90 degree straight edge, and 2" depth.
When using the Wallie Forms, you should remove the clay after forming, and should not let the clay become dry on the Forms.
2 pieces of 21 ounce duck canvas, 30" x 36" each Precision Cut to Exact Measurements Easily Replaced When Discolored or Worn Heavy Tightly Woven Design
The HydroBat Adapter allows the use of 8" and 10" bats on larger wheel heads that are not drilled to accept smaller size bats with holes 6" apart on center.
Contains center hole and a slot machined exactly to hold the Z-Brace or Bead Brace. Intended for user-made hollow dies & all beads The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
Makes any of four handle shapes for smaller objects. Requires Die Mask 925DM, which is included with die. The 4" extruder dies are made of 1/2" HDPE (High Density polyethylene). Which is extremely wear-resistant and completely non-contaminating. The top edge of the die cavity is beveled to compact the clay as it passes through, giving a crisp, more solid extrusion. In the hollow dies, there is a bevel on both the interior and exterior portions under each side of the bracket (which holds the center of the hollow dies) that helps the extrusion to "heal" after is has been cut apart by the bracket. This bracket fits into a slot machined into the top of the hollow die and is held in place by the barrel of the extruder. If a hollow die is mounted in place, the center part of the die is in exactly the right place and the wall thickness will automatically be even all the way around. In general, the walls of extrusions 3-1/2 inches OD or less are 1/4 inch thick, while larger pieces have 5/16 inch walls. We have a selection of stock 4” dies available & custom dies are quickly made and inexpensive.
The new Dirty Girls Round Bat Insert System is the best! It comes with one master bat made of an exterior grade wood material that is highly water-resistant and durable and 10 ROUND inserts that are a full 7.5" in diameter. You can throw any pot with a base 7.5" or smaller. The original Dirty Girl herself, Link Henderson throws 90% of her pots on this system. It saves tons of shelf space! The inserts are 30% larger than competitors!
There is an shallow cutout under the insert tab for placing a wooden tool to pry up the bats. There are also cutouts across from each bat pin hole on the underside of the master bat so you can easily lift the master bat off the wheel! Extra Inserts are sold in sets of 12. Do not leave submerged in water. Any wood based product left submerged in water will degrade and warp, so be nice to your bat system and gently clean the components and set them out to dry either on their sides or at a diagonal, just not stacked. If left stacked when fully wet, the inserts will swell in the center. They will dry out flat again, but it will take time!
This mold actually has a total size of 10 1/4" square, with the inner hump an 8" square. The top most flat peak is approximately 4 5/8" square with a depth of 5/8". You can trim the clay to the 8" square, or add a "lip" to your dish and trim at the 10 1/4" square.
A 12" square plaster mold containing a design resembling dragonflies. To transfer the design to your clay slab, place slab on mold, and either use a heavy clay roller, or press firmly with your hands. Remove clay from mold and shape into any form you desire.
A 12" square plaster mold containing a design resembling a tiger. An easy way to capture the feel of the animal onto your clay slab. To transfer the design to your clay slab, place slab on mold, and either use a heavy clay roller, or press firmly with your hands. Remove clay from mold and shape into any form you desire.
To transfer the design to your clay slab, place slab on mold, and either use a heavy clay roller, or press firmly with your hands. Remove clay from mold and add onto any form you desire.
To transfer the design to your clay slab, place slab on mold, and either use a heavy clay roller, or press firmly with your hands. Remove clay from mold and add onto any form you desire.
SET INCLUDES:(1) 4.5" Square Plaque(1) 4.5" x 6" Rectangle Plaque(1) 5" x 7" Oval Plaque(1) 5" x 10" Oval Plaque(1) 5" x 10" Rectangle PlaqueAll forms are measured in inches.
The HydroBat Adapter allows the use of 8" and 10" bats on larger wheel heads that are not drilled to accept smaller size bats with holes 6" apart on center.
CSI Turntables are made of two plastic laminate covered particle boards (plastic laminate design will vary from one to the other) with a stainless steel ball bearing, screwed into the inside surfaces of the boards. The 8" & 10" turntables have a 4" bearing capable of supporting at least 200# and the 12", 14" & 16" have a 6" bearing capable of supporting at least 300#. To clean, wipe with a damp sponge (do not submerge the turntable in water).
2 pieces of 21 ounce duck canvas, 24" x 36" each Precision Cut to Exact Measurements Easily Replaced When Discolored or Worn Heavy Tightly Woven Design
A 12" square plaster mold containing a design of diamonds with "saw tooth" edges on two sides. To transfer the design to your clay slab, place slab on mold, and either use a heavy clay roller, or press firmly with your hands. Remove clay from mold and shape into any form you desire.
To transfer the design to your clay slab, place slab on mold, and either use a heavy clay roller, or press firmly with your hands. Remove clay from mold and add onto any form you desire.
