Welcome to our new site. We hope you enjoy it. We are in our final testing to make sure everything is ready for you to come and SHOP. Look around all you like, we'll be officially open over here 12/26/24!
The HydroBat Adapter allows the use of 8" and 10" bats on larger wheel heads that are not drilled to accept smaller size bats with holes 6" apart on center.
The new Dirty Girls Round Bat Insert System is the best! It comes with one master bat made of an exterior grade wood material that is highly water-resistant and durable and 10 ROUND inserts that are a full 7.5" in diameter. You can throw any pot with a base 7.5" or smaller. The original Dirty Girl herself, Link Henderson throws 90% of her pots on this system. It saves tons of shelf space! The inserts are 30% larger than competitors!
There is an shallow cutout under the insert tab for placing a wooden tool to pry up the bats. There are also cutouts across from each bat pin hole on the underside of the master bat so you can easily lift the master bat off the wheel! Extra Inserts are sold in sets of 12. Do not leave submerged in water. Any wood based product left submerged in water will degrade and warp, so be nice to your bat system and gently clean the components and set them out to dry either on their sides or at a diagonal, just not stacked. If left stacked when fully wet, the inserts will swell in the center. They will dry out flat again, but it will take time!
The HydroBat Adapter allows the use of 8" and 10" bats on larger wheel heads that are not drilled to accept smaller size bats with holes 6" apart on center.
Take the guesswork out of sizing lids for your pots. One tool is all you need. Simply insert the narrow end of Lid Master into the pot, and the wide end automatically becomes a sizing guide. Use it to create lids that actually fit quickly and efficiently every time! The Large Lid Master size has an 20" capacity. Reassemble the wing nut and screw into the 12½% hole. Now you can throw a new lid for an already-fired pot without guessing the size. A typical clay shrinks about 12½% from wet to the fired state. Measure fired pot with the inside end of the Lid Master. Tighten the wing nut to lock in the measurement. Now throw a new lid using the outside end for your measurement. It will shrink to fit once it's dried and fired. Bracker's Suggestion: Don't throw away the packaging card that comes with the Giffin Lid Master. Not only help it help you remember how to use the Lid Master, it will also remind you how the washers go back onto the Lid Master when you switch between the standard 1:1 hole to the 12½% shrinkage hole.
BRIDGE #KBPC 25-06. Used in any control box that has the D30 or D30-REV control board. It is recommended to replace this whenever you replace the control board.
Keep bats from sliding on the brent® Batmobile with this well-engineered "bookend" that automatically stabilizes bats when inserted into the brent® Batmobile frame.A rubber-tipped stopper tips back the bats, holding them in place. The BatBrace will hold up to 50 12" or 14" Plasti-Bats. More than one BatBrace is recommended when supporting larger quantities of bats or bats made of heavier/thicker material. The bat brace sets on the bars of the cart and the adjustment screw is there to prop up the first bat in the series. If the cart or the bats are wet it may slide back and forth.
Faster trimming with better results! StudioPro Foam Trimming Bats offer a superior alternative to adhering the rims of pots to the wheelhead using clay coils. Because pots are held in place by the foam and not stuck down, you have the ability to lift and inspect your piece frequently during trimming. The foam also protects your pot's rim from damage while inverted on the bat. Pots can be easily centered using the concentric rings on the bats as a guide. Our Trimming Bats are made using foam selected for just the right density and grip. Keep in mind that the thicker the foam, the more unsteady smaller pieces will be during trimming, so be sure to select the correct thickness for your pots. For example, 1/4 ” foam works well for smaller, lighter work without extreme rim alteration. Whereas 3/4" foam is best used for heavier pieces or pots with uneven rims that need more protection.
The Studio Pro Bat Adapter allows the use of 8" and 10" bats on larger wheel heads that are not drilled to accept smaller size bats with holes 6" apart on center.
Take the guesswork out of sizing lids for your pots. One tool is all you need. Simply insert the narrow end of Lid Master into the pot, and the wide end automatically becomes a sizing guide. Use it to create lids that actually fit quickly and efficiently every time! The Standard size has an 11" capacity. Reassemble the wing nut and screw into the 12½% hole. Now you can throw a new lid for an already-fired pot without guessing the size. A typical clay shrinks about 12½% from wet to the fired state. Measure fired pot with the inside end of the Lid Master. Tighten the wing nut to lock in the measurement. Now throw a new lid using the outside end for your measurement. It will shrink to fit once it's dried and fired. Bracker's Suggestion: Don't throw away the packaging card that comes with the Giffin Lid Master. Not only help it help you remember how to use the Lid Master, it will also remind you how the washers go back onto the Lid Master when you switch between the standard 1:1 hole to the 12½% shrinkage hole.
Xiem Batmate™ is the perfect solution for annoying bat jitter and warping. Place Batmate™ below your problem bats on the wheel and instantly your warped bats become stable. It is also great for trimming bowls and plates. We at Xiem love ours, and we guarantee you'll love Batmate™ too.
The Hydro-Bat is made of Hydro-Stone, a USG product containing cement and crystalline silica, that is 8 to 10 times stronger then pottery plaster. The surface is scratch resistant yet absorbs water like plaster eliminating the need to cut your pieces off the bat with a wire.
The Hydro-Bat was designed to fit on wheel heads that have bat pins spaced 10 inches apart on center. The hard rubber grommets cast into the underside of each Hydro-Bat will not swell or change shape and are sized to fit over a 3/8" diameter bat pin head. Due to their smaller diameter, the grommets under the 8.5 and 10" Hydro-Bat's are spaced 6" apart and require the HBA Adapter to convert standard 10 inch pins to 6 inches. This adapter is made of sturdy polyethelene plastic and fits snuggly over the 10" bat pins on your wheel head. It has two upfacing 3/8" diameter bat pins fused in at 6” apart. The 8.5" & 10" Hydro-Bats fit onto these pins. If you have a wheel head with pins positioned at 9" apart we make Adapter HB9A which will allow you to use our bats. If you don't have bat pins in your wheel, no problem, our product works great with a bat gripper or grabber which allows you to attach any kind of bat to a wheel head. Custom adapters can be made for any size wheel head or pin configuration. The smaller Hydro-Bats (8.5” and 10” diameter) are perfect for maximizing your space when you throw smaller forms, such as bowls or mugs; because the grommets on these bats is just 6” apart, there's an adapter to make sure that they will fit onto any wheel. The smallest Hydro-Bat measures just 6” in diameter, and requires the HB6A adapter, with grommets spaced 4’ apart. All of the adapters are made of sturdy polyethylene plastic, and will become a studio staple for you along with your Hydro-Bats! If you have a pottery wheel with no drilled bat pin holes, no problem! Many customers have used Hydro-Bats with a bat gripper with great success. **this item includes a $2 per Hydrobat surcharge for deliveries and shipments via UPS/USPS or freight companies to cover the extra packing material necessary for them to get to you safely. The surcharge is added to the shipping costs.
Speedball’s Plastic Bats offer artists and instructors the ultimate in convenience, organization and performance. Their “Easy Lift Rim™” allows the bat to be easily removed from the wheel head in one fluid motion, leaving the ceramic piece undisturbed. Made from injection-molded plastic, these bats are built to last and feature unique ribs that add strength and durability. Available in 3 sizes (7.5" Square, 12" Round, 14" Round), Speedball’s Plastic Bats make organizing projects for classes and studios a breeze! Featuring universal bat pin spacing, these great bats are designed to fit all wheels and are offered at an unbeatable value.
StudioPro Tempered Hardboard Bats are the workhorses of the pottery studio. They are our most affordable bats, yet made from the finest quality tempered hardboard available. Unlike it's Masonite predecessor, our tempered hardboard has no added formaldehyde. StudioPro Tempered Hardboard Bats are slightly absorbent for good clay adhesion and bottom drying. They are compact and easy to store and will last many years if cared for properly. Hardboard bats are a great choice for the professional or hobbyist potter who uses many bats and has a controlled studio setting.
StudioPro Black Plastic Bats are a permanent solution to your bat needs. They’re easy to care for, extremely versatile, and a great choice for schools and art centers where pots are often left on bats for long periods of time. Our Plastic Bats are textured on both sides so clay adheres equally well on either surface: a true "two-sided" bat. They are cut from a high-quality marine grade High Density Polyethylene (HDPE), which is produced using a patented extrusion process. This ensures perfect flatness of every sheet and every bat! All bats are 1/4" thick EXCEPT for the 22" diameter bat which is 3/8" thick. The 8" and 10" bats work with the 12" bat adapter.
StudioPro SpaceSaver Bat System The SpaceSaver is a convenient system for making smaller pots and maximizing table space in your studio. The entire system is fully compatible with the now unavailable Wonderbat. It consists of a 14" adapter bat and 8- 6" insert bats. Both are made from a 1/2" exterior grade MDF which provides excellent bottom drying and rigidity. The adapter bat mounts on standard wheel-head pins with rubber "through hole" grommets making a true two-sided bat. Made from 1/2" exterior grade MDF "finger lifts" and rounded edges for easier removal, smoothness and longer wear Excellent bottom drying Rubber grommets spaced 10" on center for standard wheel pins Through-hole grommets make the SpaceSaver a true two sided bat
StudioPro Tempered Hardboard Bats are the workhorses of the pottery studio. They are our most affordable bats, yet made from the finest quality tempered hardboard available. Unlike it's Masonite predecessor, our tempered hardboard has no added formaldehyde. StudioProTempered Hardboard Bats are slightly absorbent for good clay adhesion and bottom drying. They are compact and easy to store and will last many years if cared for properly. Hardboard bats are a great choice for the professional or hobbyist potter who uses many bats and has a controlled studio setting.
